Desiccant Air Dryer
SEAH INDUSRTRY
Heatless Type
- Heatless type desiccant air dryer
It is the desiccant equipment to fill high alumina gel having mositure and chemical attraction into the
tank in order to supply the pressure air of saturation come from air compressor under high dry status,
A typical regenerative dryer consists of two towers charged with activated alumina desiccant.
One tower dries air, while the desiccant in the other toweed with low pressure and low pressure
and low humidity air.
Often ,heat is added to assist the regeneration process. In this design, a small amount of the dried
air (from the drying tower) is expanded to near atmospheric pressure in the regenerating tower.
The dry air becomes super dry on expansion, and readily absorbs the moisture from the saturated
desiccant bed.
Like this, the machinery to reiterate the dehumidification and regeneration under allowed time and
then, supply the dried air is called as " Desiccant air dryer ".
Among above, heatless dryer is "Heatless type desiccant air dryer" and pressure air of 5-15% is utilized
in order to regenerate a desiccant due to heatless.
SHL series offers the maximum in reliability. A solid state timer and valves cootrol the entire drying and
regeneration process.
Generally, Our system uses a 10 minutes ( 5 minutes ) cycle ; 5 minutes ( 2 minutes 30 seconds ) drying,
3 minutes 50 seconds ( 2 minutes ) regeneration and 1 minute 10 seconds ( 30 seconds ) repressurization.
- Pneumatic aquamatic valve in which operations is sure and there is no trouble is utilized.
- P.C.B ( Printed Circuit Board ) equipped with micro-processor is set.
- Super dried air from pressure dew point -40c to -73 is produced.
- Safety valve is equipped with tank for user`s safety
- A high quality activated alumina is utilized.
- Filter is installed into control line and there is no iner trouble on the machinery.
- Installation , repairing and maintenance are easy and if the desiccant and consumpables are
exchanged periodically, it can be utilized semi-permanently.
Model |
Capacity |
in / out |
Gel |
Dimension ( mm ) |
Weight | ||
Nm3/hr |
inch |
kg/Tower |
Width |
Depth |
Height |
kg | |
SHL 25 |
43 |
1/2 PT |
13 |
840 |
308 |
1,010 |
60 |
SHL 35 |
60 |
3/4 PT |
18 |
840 |
308 |
1,270 |
75 |
SHL 45 |
85 |
3/4 PT |
25 |
840 |
310 |
1,520 |
100 |
SHL 75 |
128 |
3/4 PT |
38 |
840 |
310 |
2,030 |
160 |
SHL 100 |
170 |
1 PT |
50 |
1,150 |
430 |
1,830 |
230 |
SHL 125 |
213 |
1 PT |
57 |
1,150 |
430 |
1,830 |
260 |
SHL 150 |
255 |
1 PT |
63 |
1,150 |
490 |
1,854 |
270 |
SHL 175 |
297 |
1-1/2 PT |
75 |
1,150 |
490 |
1,854 |
284 |
SHL 200 |
340 |
1-1/2 PT |
87 |
1,150 |
490 |
1,854 |
310 |
SHL 285 |
425 |
1-1/2 PT |
124 |
1,270 |
555 |
1,880 |
405 |
SHL 350 |
624 |
1-1/2 PT |
174 |
1,270 |
595 |
1,880 |
470 |
SHL 430 |
850 |
2 PT |
248 |
1,400 |
645 |
2,185 |
650 |
SHL 560 |
1,105 |
2 PT |
322 |
1,400 |
700 |
2,185 |
720 |
SHL 720 |
1,370 |
3 FLG |
397 |
2,100 |
890 |
2,413 |
900 |
SHL 900 |
1,700 |
3 FLG |
496 |
2,100 |
890 |
2,413 |
1,130 |
SHL 1100 |
2,040 |
3 FLG |
595 |
2,100 |
890 |
2,413 |
1,300 |
SHL 1350 |
2,380 |
3 FLG |
694 |
2,590 |
1,050 |
2,590 |
1,580 |
SHL 1550 |
2,720 |
4 FLG |
798 |
2,590 |
1,050 |
2,590 |
1,760 |
SHL 1800 |
3,060 |
4 FLG |
862 |
2,590 |
1,050 |
2,590 |
1,980 |
SHL 2100 |
3,400 |
4 FLG |
998 |
2,590 |
1,050 |
2,590 |
2,200 |
SHL 2250 |
3,825 |
4 FLG |
1,123 |
2,590 |
1,205 |
2,590 |
2,480 |
SHL 2500 |
4,250 |
4 FLG |
1,248 |
2,590 |
1,205 |
2,590 |
2,700 |
SHL 2750 |
4,675 |
4 FLG |
1,361 |
2,590 |
1,205 |
2,590 |
2,970 |
SHL 3000 |
5,100 |
6 FLG |
1,497 |
2,590 |
1,205 |
3,200 |
3,240 |
SHL 3500 |
5,950 |
6 FLG |
1,747 |
3,100 |
1,360 |
3,400 |
3,830 |
SHL 4100 |
6,800 |
6 FLG |
1,996 |
3,100 |
1,360 |
3,400 |
4,400 |
※ Capacity based on inlet temperature 38 ℃ , working pressure 7kgf/cm2G , Dew point -40 ℃.
※ Standard desciccant is the activated alumina gel.
※ Heat exchanger equipped with dryer more than "SHI 430" is test acquired by
KOSHA ( Korea Occupational Safety and Health Agency ).
※ Standard voltage is 220V / 1 / 60 Hz, non standard is available.
※ Up to dew point -73.3 ℃ can be manufactured accordering to ordering.
※ Desiccant is supplied after filling to the tank less than "SHL 1100", but if more than it,
it is shipped under seperation.
※ Be careful that above specification can be changeable at any time without any prior notice
in order to to upgrade the quality and performance of the products.
.